AireRyder LK51215OR Manuel d'instructions télécharger pdf

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless

additional support is provided for the fan.

LK51215

1. Remove the switch box cover from the switch box of

the fan by loosing the three switch box screws.

2. Unscrew the center plug from the switch box cover

and discard it. (Fig.1)

3. Slip the short nipple up through the pull chain, and

secure it into the coupling with hex nut. (Fig.3)

4. Slip the tube, small cap with the open side facing

upward and the big cap with the open side facing

downward up through the pull chain and the short

nipple, secure them together with a hex nut.

5. Thread the fixture wire through the switch box cover.

(Fig.1)

6. For fan style that is shown in Fig.1: Attach the nipple

of the light kit to the hole of the switch box cover, then

thread the wires through the washer and hex nut,

then secure them tightly.

7. For fan style that is shown in Fig.2: Thread the fixture

wire through the switch box, then attach the light kit

to the switch box and secure it with two set screws

(6x32 20mmL).

8. Cut the redundant wires if necessary. Pull out the wires from the switch box. Make wire connections

using the wire nuts:

---The black wire from the light kit to the black (or blue) wire from the switch box.

---The white wire from the light kit to the white wire from the switch box.

Carefully put the wires back into the switch box.

9. Attach the switch box cover back to the switch box using the three switch box screws.

10. Install bulbs (included). See relamping label at socket area or packaging for maximum allowed wattage.

11. Slip the glass shade and decorative ring up through the pull chain and the short nipple, secure them with

a hex nut.

12. Slip the cover up through the pull chain and the short nipple, secure it with finial.

13. Turn on the power at the main fuse or circuit breaker box.

(You can control the light with the pull chain)

LK51215 --- Page 1

Coupling

Pull Chain

Big Cap

Glass Shade

Hex Nut

Short Nipple

Tube

Small Cap

Hex Nut

Decorative Ring

Hex Nut

Cover

Finial

For Light Kit:

Light Kit

E26 medium base spiral

fluorescent Bulb

(Max.13W, incluced)

Fig.1

Motor

Switch Box

White Wire

Hex Nut

Screw

Switch Box Cover

Nipple

Light Kit

Wire Nut

Washer

Center Plug

Black or Blue Wire

Black Wire

Fig.3

Motor

(6 x 32 20mmL)

Set Screw

Fig.2

Nipple

Screw

Black or Blue Wire

Wire Nut

Black Wire

Motor

Switch Box Cover

White Wire

Terminal (Groove)

Terminal (Tongue)

White Wire

Switch Box

090406

F A N C OF A N C O

1 2

Résumé du contenu

Page 1 - INSTRUCTIONS

ASSEMBLY AND INSTALLATION INSTRUCTIONSWARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUITBREAKER BOX BEFORE INSTALLING OR

Page 2 - For Semi-Flush

1. Take out the parts from the hardware package For Semi-Flush. 2. Attach two screws to the mounting strap, and secure it with two lock nuts.

Commentaires sur ces manuels

Pas de commentaire

AireRyder LK51215OR Manuel d'instructions

Naviguer en ligne ou télécharger Manuel d'instructions pour Ventilateurs des ménages AireRyder LK51215OR. AireRyder LK51215OR Instructions / Assembly Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Ventilateurs des ménages AireRyder LK51215OR